유레카샵 / 무선조종 RC카 자동차 헬기 비행기 드론 [Tarot(DJI) 고사양 고성능 멀티콥터 드론 F450 CC3D/변속기/모터/프롭 포함 *미조립 버전]

· 2KG 급 멀티콥터에 사용 가능한 멀티콥터 전용 모터입니다.

· 고속용 베어링이 적용되어 있어 모터 회전시 진동이 없습니다.

· 내부 스테이터가 0.2 슬림 실리콘 스틸과 특수 내열 네오디뮴 자석으로 제작되어 높은 열에도 내구성이 강합니다.

주의: 은색 캡이 포함되어 있는 모터는 정방향(위에서 보았을 때 반시계방향)용 모터이며, 검정색 캡이 포함되어 있는 모터는 역방향(위에서 보았을 때 시계방향)용 모터입니다.

1 Specification

1.1 Output: Continuous 20A, Burst 25A up to 10 seconds.
1.2 Input Voltage: 2-3S Lipo, 5-9 cells NiMH.
1.3 BEC: 2A / 5V Linear mode BEC.
1.4 Refresh rate of the throttle signal: 50Hz to 432Hz.
1.5 Max Speed: 210000rpm for 2 Poles BLM, 70000rpm for 6 poles BLM, 35000rpm for 12 poles BLM.
(BLM = BrushLess Motor)
1.6 Size: 42mm*25mm*8mm.
1.7 Weight: 19g.

2 Features

2.1 Safety arming feature: Regardless the throttle stick position, the motor will not spin after battery connected.
2.2 Throttle calibration funtion: Throttle range can be calibrated to be compatible with different transmitters.
2.3 User programmable.
2.4 Multiple program methods supported: transmitter stick, LED Program Card. Very easy to program the ESC at home or at the flying field.
2.5 Compatible with Lipo and NiMH battery.
2.6 Timing can be changed to be suitable for different brushless motors.
2.7 Full protection: Low voltage cutoff protection / Over-heat protection / Throttle signal loss protection.

[TAROT] 9인치 자동잠김 프로펠라 X 4개 포함 ( 색상 랜덤 )

제원 :

회전시 직경 : 9 inch
높이 : 18.3MM
피치 : 4.5 inch
크기 : 9x4.4
무게 : 13.0G/1개

사이즈:40X40X14 mm(외부박스포함)

무게:15.2g(외부박스포함)

오픈 파일럿 CC3D 보드는 내부는 CC3D보드이고 외부는 옵션보호케이스가 달린케이스가 카버되여있습니다.

위성수신기 장착할수있습니다.

수신기/아우트푸트/브레이크아우트 케이블(8핀) 및 두개 (4핀) 병렬케이블/i2c(Flexiport) 케이블.

부트로더(Bootloader)는 간단한 소프트웨어를 통해 V4까지 업그레이드 할수있습니다.

특징:

- S.BUS, CPPM, Spektrum(스팩트럼) 위성 및 PWM 서포트

- Mac OS X, Linux and Windows 소프트웨어 서포트

-Tricopters(트리콥터), Quadcopters(퀘드콥터) and Hexacopters(헥스콥터) 에 전부사용가능

- 고정익비행기 및 플라이바리스 헬리콥터(flybarless helicopter)에도 자이로 기능으로 사용가능

- firmware 업그레이드하거나 세팅시 온보드 미니USB 사용/*FTDI는 필요없음

-6-axis 모션/포지션 센서 (32-bit MCU) MPU6000 /*( Naze32 및 Mullet 보드와 같은 기능)
The CC3D has been designed from the ground up to perform the following functions:

a MultiRotor controller with auto-level, including TriCopters, QuadCopters and HexaCopters
a Flybarless Helicopter controller with auto-level
a Fixed Wing UAV controller

CC3D controller features:

Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer
Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.
Software support for Windows, Mac and Linux
Direct high speed USB support with no drivers required, a truly plug and play device.
Spektrum satellite receiver support
Futaba S-BUS hardware support
Innovative Flexi-port technology for superior port flexibility
4Mbits on-board EEPROM for configuration storage

Flexiport:
CopterControl also offers the innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs.

Superior user experience
OpenPilot has tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe.

The OpenPilot project, whist still young, it trying to make Open Source much more user friendly. OpenPilot software is designed to be used by everybody! All major operating systems are supported and install packages are provided. The software is all Free software under the GPLv3 license and not only are you welcome to hack it, but we encourage it!

Sensors and Components:
3-axis Gyroscope array and 3-axis Accelerometer: MPU-6000
Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2, DSMJ, DSMX satellites, and Futaba S.Bus receivers
Simultaneous support for multiple receivers
ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channels
MainPort functions (configurable): serial telemetry (default), GPS, S.Bus, Spektrum/JR satellites
FlexiPort (configurable): serial telemetry, GPS, Spektrum/JR satellites, or I2C peripherals (under development)
10 PWM outputs to servos or ESC’s, or for camera stabilization
Camera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers
Onboard USB connectivity for easy configuration
USB and serial telemetry and configuration (including wireless with optional radio modules)
Supported by powerful OpenPilot GCS
4 Mbit onboard memory
3C Quaternion based complementary filter running at 500Hz

4채널 조종기(수신기포함)

7채널 조종기(수신기 포함)

아래부터는 옵션 상품입니다. 구가구성/옵션메뉴에서 추가 가능.

- 옵션 스키드 -

스키드 장착을 위한 M2.5x8 나사 8개가 포함되어 있습니다.

- 옵션 FPV 스키드 -

EP Power 2200mAh 11.1V 30C 리튬폴리머 배터리 EC3 잭

*EC3잭 과 XT60잭은 호환이 됩니다!

Specifications:
- Discharge Rate:20℃
- Burst Rate: 30-35℃
- Connector: EC3
- Size : 105 X 32mm X20mm

- Weight : 170g
- Charging tempearture: 0℃ ~ +45℃
- Operating temperature range: -10℃ ~ +80℃

조립공구

티타늄 육각 렌치 4종 세트
RC 자동차 비행기 헬기 등에 가장 많이 사용되는 규격 세트 입니다.

구성 : 육각렌치 1.5, 2.0, 2.5, 3.0mm 4종 세트

7채널 조종기(수신기 포함)